The best brake controller for your 2019 Ford E-450 Cutaway is the Redarc Tow-Pro Elite Trailer Brake Controller item # RED44FR. The Tow-Pro Elite is very similar in design to a factory trailer brake controller. There is a control box that gets installed under the dash, out of sight and then a control knob that gets mounted on your dash wherever you prefer. This will provide a very clean look and will allow you to mount it in many different locations whereas a standard brake controller will... view full answer...
Thank you for the picture that really does help figure out what'll be best for you.
It appears for your right/left rear outside tires, you could benefit from an extender that has a bend in it, like the Wheel Masters Tire Pressure Valve Extenders - 135-Degree Bend # WM8029135.
For your inside tires, I'd recommend going with a simple straight extension like the Wheel Masters Tire Pressure Valve Extenders - Straight # WM80293 which measures 3" long.
We also have those straight extenders... view full answer...
The install harness part # 3034-P that you referenced has been confirmed as a fit for installing a brake controller in your 2016 Ford E-450 RV. I attached a picture that shows which panel you will find the harness behind (even though it sounds like you found it already.
For a brake controller I would recommend the Prodigy P2 Brake Controller part # 90885. This is our best selling brake controller because of how well it works and how easy it is to setup. This is a proportional brake controller... view full answer...
We have several great and different options for tire chains for the size 225/75R16 that you have on your RV. The absolute best and easiest option is the Easy Fit part # TH04115245 which install in a matter of seconds, provide great traction, and also will last the longest. The are higher in price.
If you wanted a higher quality chain with a lower price that would take a bit longer to install the Konig standards part # TH01571245 will offer great traction and last a long time but will... view full answer...
For a windshield cover that is confirmed as a fit for your 2019 Sunseaker built on a Ford F-450 chassis we have the Adco Cover part # 290-2507 which would fit and work well. view full answer...
Yes, for your Fleetwood Jamboree built on a Ford E-350 chassis we have the Roadmaster steering stabilizer part # RM-1139-117 as a confirmed fit for the rear bar and then part # RM-1139-115 for the front. view full answer...
I looked up your 2017 Thor Windsport Coach and it uses a single pull out step just like the Kwikee 28 Series part # LC3747453 that you referenced so this would easily replace what you have and work well. It will pull out automatically when you open the door and retract when you close it. view full answer...
Is your motorhome on a Ford F450 truck Cab/Chassis or a E450 Van Cutaway Chassis?
If it's equipped with a 7-way trailer connector, it'll likely be prewired for a brake controller. On the truck cab/chassis, the brake controller connector which is gray in color would typically be located above the driver's right knee, under the dash. On the van chassis, it would usually be found to the left of the steering column. If the connector is present, it should be a plug and play installation.
For... view full answer...
I always respect the manufacturers posted weight ratings when towing and hauling, I never push to the max and caution against exceeding those ratings. OEM's are required to complete rigorous testing before a vehicle is released for sale, this testing has been developed over decades of process improvements. Personally I prefer to stay at least 10 percent below the max rating for payload, towing and combined weights but I caution against exceeding them in any way.
You state "...need to... view full answer...
I spoke with my contact at Draw-Tite, and if your motorhome was built on a 2017 Ford F-450 Chassis, then the Draw-Tite Front Mount Trailer Hitch Receiver # 65076 is confirmed to fit and will work great. This hitch has a line pull limit of 9,000 pounds and vertical load limit of 500 pounds. No welding will be required during installation and the complete hardware kit is included.
I have attached the installation details for you to review. view full answer...
For your 2017 Ford F-550 Cab and Chassis, you will need to do some custom fabricating to have a gooseneck hitch option. There is not a custom fit frame bracket available that is a fit. I recommend the B&W Turnoverball Underbed Gooseneck Trailer Hitch for Flatbed Trucks - 30,000 lbs # BWGNRK1500 that will require custom welding to install. I've attached the installation details so you can see what will be required for this hitch to be compatible. view full answer...
For your 2019 Ford E-450 Cutaway, I recommend using WeatherTech All-Weather Front Floor Mats part # WTW51 for black, part # WTW51GR for gray, or part # WTW51TN for tan. Like you said, the manufacturer does not recommend using these or the thermoplastic option because you have the vinyl flooring. These recommendations are ruber, and not thermoplastic.
The above floor mats are all custom fit options which means they are contoured specifically to match the footwell in your cutaway. I have... view full answer...
The install harness you'd need for your 2017 Ford F-450 is the part # 22292 for the P2 part # 90885 that you bought.
I attached an install video that shows the entire process. view full answer...
Doing some research on your 2017 Jayco Redhawk, it looks like it has a Ford E-450 chassis. If that is the case, then we do offer some custom fit floor mat options that will work great.
For the best option that complements all interior colors, I recommend the WeatherTech Front Auto Floor Mats # WT26DV. These black mats are custom-designed to fit the exact contours of your vehicle. Also, the mats come with the WeatherTech lifetime warranty and are 100% made in the U.S.A.
To keep the mats... view full answer...
Best option would be to use a rubber grommet that fits the hole that the cam lock fit into after installing the Global Link Locking Baggage Lock Actuator Set with Mounting Plate # GL34FR. You'll need to measure the diameter of the hole after removing the lock and go with a grommet that is the same size. view full answer...
The brake controller I recommend as the best for your 2020 Ford E-450 chassis is the Redarc Tow-Pro Elite Trailer Brake Controller part # RED44FR. This controller is very similar in design to the factory brake controller Ford would have installed in your truck but it does perform much better. There is a control box that gets installed under the dash, out of sight and then a control knob that gets mounted on your dash wherever you prefer.
The correct plug-in harness you will need is the... view full answer...
Yes, the Pulse Preventer for Electric Brake Controllers # 5501 is exactly what you need to keep the EOH actuator from activating while your hazard lights are on.
Hazard lights are tied into the stop light switch just like your Prodigy P2 # 90885 is. That is why the P2 will send a pulse signal when the hazards are activated on your 1997 Ford F-450. view full answer...
Go To Results